CrossFit Brandon, FL

Header Woman

A Step-By-Step Guide To A Perfect Jerk

A Step-By-Step Guide To A Perfect Jerk

When it comes to Olympic weightlifting, the snatch and clean get the most attention. The jerk just doesn’t get the same amount of love. As a trainer, I’ll take some of the blame. My weightlifting teaching progressions address the snatch first, followed by the clean, with the jerk bringing up the rear.

Although this approach is logical, the lifts shouldn’t be judged in this order in regard to complexity or merit. The jerk is every bit as technical and challenging as the clean or snatch.

In this article, we’ll take a look at the entire jerk movement from start to finish, and detail exactly what you should be doing at each stage to ensure a safe and successful lift.

 

The Grip

A good jerk starts with the barbell in a solid rack position with a proper grip. The grip width for the jerk should be just outside your shoulders. If you have large biceps and/or a tough time externally rotating your arms while gripping the barbell, then a wider grip may be required.

 

“A good jerk starts with the barbell in a solid rack position with a proper grip. The grip width for the jerk should be just outside your shoulders.”

Once you’ve securely gripped the bar, raise your arms until your triceps are parallel to floor, similar to the position used in a front squat.

Your wrist should be slightly cocked with the barbell gripped securely.

If you’ve got poor shoulder or thoracic mobility, then you’ll need to let the barbell roll onto the tips of your fingers in order to get into a solid lifting position. 

 

 

The Stance

The jerk primarily uses the lower body and trunk to dynamically get the barbell overhead. It’s also difficult to wind up and subsequently release the stored energy in your hips while employing a narrow stance.

 

jerk, grip, dip, overhead, clean and jerk, stance, drive, split jerk, lock out

 

The Dip-Drive

When you are ready to execute the dip-drive of the jerk, take a large belly breath and hold it. This will help protect the lower back and transfer energy from your legs through the trunk to the barbell.

 

“The jerk relies heavily on the tension of your musculature in order to generate force. If this phase looks slow and sluggish, like a wet sponge, then you’re doing it wrong.”

To start the dip, slightly flex at the knees, pushing them out like you would in a squat. This movement should occur quickly. It’s a shallow and violent movement.

 

The drive phase is simply a redirection of force. This action is largely dependent on creating tense musculature throughout the legs and trunk, while quickly extending the knees, ankles, and hips. It’s important we drive through the heels during this step. You may end up on the forefoot or toes, but that should be a symptom of your natural kinesthetics – not a contrived effort.

The jerk relies heavily on the tension of your musculature in order to generate force. If this phase looks slow and sluggish, like a wet sponge, then you’re doing it wrong.

 

Jerk dip drill.

 

The Receive Position

Once the drive is initiated, the barbell should hop up with some zip. It will become weightless for a split second before reaching its apogee. It’s at this point that you need to aggressively drop under the bar into a split jerk receiving position.

 

The Lock-Out

A slight internal rotation of the front foot will help create a stable split receiving position. The downward motion of the rear knee helps create relaxed flexion, enabling you to adjust depth based on the outcome of the drive phase. This position also prevents tight lifters from getting stuck in the split because they’ve reached their end range of motion in the anterior hip capsule of their rear leg.

 

“You don’t want to literarily drive the knee into the ground, but it helps to think that way in order to create a stable base.”

When you’re in this split position, imagine we painted a circle on the platform the size of a large hula-hoop. Your feet should be in contact with the inside edge of that hoop. If your rear foot is way back and outside the hoop, then it’s a problem.

 

 

The Recovery

When the bar is locked out overhead and you’re in a stable split position, then it’s time to stand the weight up. This is easily done by taking a half-step back with the forefoot, bringing the rear foot a half-step forward, and then repeating that process.

 

It’s important your feet are parallel to one another on the platform. At this point, and you’ll need to have control of the barbell overhead. Again, failure to do so will result in a “no lift” during a meet.

 

Never ghost ride or drop the barbell from overhead. I always encourage my athletes to maintain control over the bar until it descends to their mid-thigh.

 

Summary of the Split Jerk

The jerk requires a great amount of athleticism, concentration, and timing in order to do it well. Remember Rome wasn’t built in a day, but it burned in one. Take your time and use reasonable weight while learning this lift.

 

The jerk is a demanding lift that can help a wide range of trainees when done properly.”

An Interview by our very own Eric Auciello(Courtesy of breakingmuscle.com )
Read the rest here:

http://breakingmuscle.com/fitness/a-step-by-step-guide-to-a-perfect-jerk

Comments are closed.